Airlink101 AWLC3026T Manual de usuario

802.11g CardBus Adapter Model # AWLC3026T User’s Manual Ver. 1A

10 Step 3 Expand Network adapters from the list and verify that Airlink101 802.11g CardBus Adapter is listed and no yellow question mark is beside it

11 3. Configure the Cardbus Adapter This section describes how to connect your 802.11g CardBus Adapter to a wireless network. Note to Windows XP Use

12 To open the Cardbus Adapter’s utility go to Start > (All) Programs > Airlink101 802.11g CardBus Utility > Airlink101 802.11g CardBus Utili

13 Step 2 If encryption is not enabled for the selected access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless sett

14 Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next. Step 5 Follow the

15

16 Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quali

17 4. Configure the Wireless Utility This section describes the various functions of the Wireless Utility that you can configure, including the setti

18 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Streng

19 4.2 AP List The AP List tab displays all the available Access Points detected by the Cardbus Adapter. Simply select the desired Access Point you w

2 Table of Contents 1. Introduction...

20 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Cardbus Adapter. Note: The encryption setti

21 Step 3 Verify the Network Name (SSID) is correct and click Next. For WEP Settings: WEP Step 4 Select the appropriate Authentication Mode and En

22 WEP Step 5 Select the appropriate Input Method, Key (password), Key Index, and click Next. WEP Step 6 Click Complete to finish the settings.

23 For WPA Settings: WPA Step 4 Select WPA-PSK and the appropriate Input Method and click Next. WPA Step 5 Enter the WPA Key (passphrase) and clic

24 WPA Step 6 Click Complete to finish the settings. Step 7 You should see a blue circle around the antenna icon indicating a valid connection. A l

25 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environment

26 Step 2 Enter a name for your new profile and click Next. Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and

27 Step 4 Configure any encryption setting if required and click Next. Step 5 Click Complete to finish the profile setting.

28 Step 6 Your new profile will be listed in the Profile List. Step 7 You can quickly select which profile you want to use from the Link Informatio

29 4.5 Static IP Setting To change the IP address of the wireless adapter to Static IP, follow the steps below: Step 1 On the last step of 4.4 Profi

3 1. Introduction Thank you for purchasing the 802.11g CardBus Adapter. This CardBus Adapter is designed to comply with IEEE 802.11g Wireless LAN sta

30 4.6 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the 802.11g CardBus Adapter.

31 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoretic

4 2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the 802.11g CardBus Adapter. The driver is i

5 Step 2 Click Next at the welcome screen. Step 3 Click Next to accept the default destination folder.

6 Step 4 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). Step 5 Verify

7 Step 7 Select Install the software automatically and click Next. For Windows 98SE and ME, select Search for the best driver for your device and

8 Step 9 Click Finish. (Restart the computer for Windows 98SE and ME).

9 2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on